Generic Exome Analysis Plan

This page outlines a generic plan for analysis of a whole exome sequencing project. The idea is that the points listed here might serve as a starting point for discussion of the analyses needed in a specific project.

Read Mapping and Variant Calling

The first step in any analysis is to map sequence reads, callibrate base qualities, and call variants. Even at this stage, some simple quality metrics can be evaluated and will help identify potentially problematic samples.

Prior to Mapping

Evaluate Base Composition Along Reads

Calculate the proportion of A, C, G, T bases along each read. Flag runs with evidence of unusual patterns of base composition compared to the target genome.

Evaluate Machine Quality Scores Along Reads

Calculate average quality scores per position. Flag runs with evidence of unusual quality score distributions.

Calculate Number of Reads

Calculate the input number of reads and number of bases for each sequenced sample

Read Mapping

Map Reads with Appropriate Read Mapper

Currently, [bio-bwa.sourceforge.net/bwa.shtm BWA] is a convenient, widely used read mapper.

Basic Mapping Statistics

We should tally the overall proportion of mapped reads.

We should also tally the proportion of reads that map

• Inside the target regions
• Near the target regions (defined as within 200bp of each target)
• Elsewhere in the genome (defined as regions that are >200bp from each target)

Recalibrate Base Quality Scores

Base quality scores can be updated by comparing sites that are unlikely to vary (such as those not currently reported as variants in dbSNP or in the most recent 1000 Genome Project analyses.

Update Base Quality Score Metrics

Generate new curves with base quality scores per position.

Calculate the number of mapped bases that reach at least Q20. Potentially, calculate Q20 equivalent bases by summing the quality scores for bases with base quality >Q20 and dividing the total by 20.

Verify Sample Identities

Verify that Each Sequenced Sample Matches Prior Information

We should verify that each sequenced sample matches previous genotypes for that sample. Ideally, this should be done using a likelihood based approach that can also identify potentially contaminated samples.

Adjudicate Mislabeled Samples

If any samples that don't match prior genotype data are encountered, the read data for these samples should be compared to all available samples to identify potential sample mixups.

Identify Potentially Related Samples

Perhaps this step should be done *after* variant calling?

Generate Variant Calls

Generate Initial Set of Variant Calls

Variant calls should be generated taking into account all available samples simultaneously. We should consider variants calls that fall in target regions but also those that fall near the target. An open question is whether off target variant calls will be trustworthy.

Generate Linkage Disequilibrium Aware Set of Variant Calls

A typical exome call set might include many sites where no variant is called due to low coverage. If we can integrate samples with previous GWAS data, we should be able to generate an update and much improved set of variant calls for each individual.

Annotate Functional Impact of Each Variant

Called variants should be annotated according to their potential function. At a minimum, we should distinguish synonymous, non-synonymous, conserved splice site, 5'UTR, 3'UTR and other variants. Ideally, we should also assess SIFT and PolyPhen scores for conserved variants.

Calculate Overall Frequency Spectrum

Calculate observed frequency spectrum and compare to neutral expectations (which are that the number of variants should be roughly proportional to 1/n, where n is the number of minor alleles).

Annotate Overall Variant Characteristics

Calculate overall ratio of transitions to transversions, separately for coding and non-coding variants. Within coding variants, analyse synonymous and non-synonymous variants separately.

CpG Sites

Calculate the rate of per base pair heterozygosity at potential CpG sites and compare this to other sites.

Tabulate for Each Sample

• The number of synonymous and non-synonymous variants
• The number of unique and shared variants
• The number of transitions and transversions

Evaluate Variant Calls for Reference Samples

If Previously Sequenced Samples Available, Assess Variant Calls There

Assess concordance rate at non-reference sites

If Duplicate Samples are Available, Assess Concordance

Assess concordance rate at non-reference sites.

If Nuclear Families are Available, Assess Mendelian Consistency

When reporting rates of Mendelian inconsistencies, report these not on a per site basis but, instead, based on the number of sites with at least one non-reference call in the trio.

Special Considerations for Admixed Samples

Estimate Local Ancestry Using GWAS Data

For studies that include admixed samples, we should estimate local ancestry using GWAS data. If GWAS are not available, it is strongly recommended that these data should be generated. In principle, local ancestry estimates can be generated even before exome sequencing is complete.

Estimate Global Ancestry Covariates Using PCA or MDS Analysis

Initial Association Analyses

We anticipate that, at least early on, the initial association analysis of whole genome datasets in the context of complex trait association studies will focus on identifying and resolving quality control issues that might result in unexpected artifacts.

Initial Single SNP Tests

In principle, these tests only have power for common variants. In practice, particularly when permutation based methods are used to assess significance, there should be little loss in power by testing all variants using single SNP tests. These tests should include:

Logistic Regression Based Tests for Discrete Traits

Discrete outcomes should be evaluated using logistic regression. It is important to include appropriate covariates. For most traits, these might include age and sex and, potentially, principal components of ancestry.

Linear Regression Based Tests for Quantitative Traits

For quantitative traits that are not strongly selected, linear regression based tests can also be used. Again, it is important to include an appropriate set of covariates. For many quantitative traits, it may be a very good idea to normalize traits to minimize the impact of outliers on association results.

Using genotypes as outcomes for Selected Quantitative Traits

For both discrete and quantitative traits, analysis can be repeated using genotypes (scored as 0, 1 and 2) as outcomes and phenotypes as predictors.

Q-Q Plots

After carrying out initial single SNP tests, generate Q-Q plots for each analysis. Verify that Q-Q plots are reasonable and that genomic control value is close to 1.0. If not, refine sample and variant filters as needed.

Burden Tests

The same analyses that were originally carried for single variants should be carried out for groups of rare variants. In principle, one could simple use the presence of a rare variant (or a particular class of rare variant, such as a non-synonymous variant or a newly discovered variant) as a predictor and repeat the logistic regression, linear regression or genotype regression described above. For an initial pass, I think the precise form of this analysis is not critical, because the next step is to...

More Q-Q Plots =

After carrying out initial burden tests, generate Q-Q plots for each analysis. Verify that Q-Q plots are reasonable and that genomic control value is close to 1.0. If not, refine sample and variant filters as needed.

Visualize Results =

A number of displays will likely be useful. Probably these should include:

• Manhattan Plots
• LocusZoom Plots
• Q-Q Plots

Think You Are Done?

No way!!!

Indels and Structural Variants

You still need a plan to call and evaluate short insertions and deletions as well as larger structural variants.

Pathway Based Analyses

Carry out analyses that include groups of genes with similar biological function (for example, according to Gene Ontology or Kyoto Encyclopedia of Genes and Genomes annotations.